You would require at least an Editor AvoKey to use v12 and above versions of the PC Suite for your offline programming. PC Suite v11 still appears to be supported and available for download, v11 does not require an AvoKey, v11 only requires a free licence file issued by Avolites. Show files are forw...

I don't know about unassigned and couldn't guess at it either. I don't use the mobile wing either but - http://localhost:4430/titan/handles/MobileWingAPlaybacks Might get you what you need, the wing probably has to be present/connected otherwise you'll most likely get an "Request for unknown gr...

I suspect you are already aware of this but just in case, it does not seem possible to get information on all playbacks with the level of detail you require from a single request. You can get basic detail for all playbacks with - http://localhost:4430/titan/handles/Playbacks Then, for each playback ...

Titan Go V15 The handle view (,the display area above fader playbacks,) for chases always shows the local chase speed and ignores or fails to account for any speed source selection. This results in the handle view showing incorrect chase speed values when the chase's speed source is allocated to a B...

Titan Go V15 When applying offsets to attributes via the "<Record>, select palette, [Update Offset]" method, the offset calculation appears to assume, and depend on, the attribute range being 0~100. The resultant offset value is incorrect for any attribute with a range that is not 0~100. R...

Titan Go V15 When attribute values are limited to values less than zero, the associated wheel view does not display the "LIMITED" watermark. Repro as follows - 1. Start new show 2. Patch 1 x Varilite VLZ Profile [16-Bit Enhanced, 61 DMX] 3. Select VLZ Profile and set "Frame Rot" ...

Titan Go V15 When setting attribute lower limits the system prompts "Set the Lower Limit value (percentage)...". However, depending on the attribute value range (i.e. an attribute with a range outside of 0~100), setting the lower limit as a percentage can have no affect. Repro as follows -...

Titan Go V15 When setting attribute upper limits the system prompts "Set the Upper Limit value (percentage)...". However, depending on the attribute value range (i.e. an attribute with a range outside of 0~100), setting the upper limit as a percentage can result in the attribute value bein...

Thanks for taking the time to investigate and log the issue Gregory. As the intention is to remove the options until the underlying feature is available then you should probably note, if you haven't done so already, that the user manual should also be revised to remove mention of these options for c...

Thanks for taking the time to look into it Gregory, I assumed it was more likely the animation parameters that were the issue but I needed to include an element to animate for the repro.

Thanks for looking into it Gregory, Yes, it does look like it is just the indicator that's the issue. I can't say for sure on all the trigger types as I was only using sACN but certainly that actual trigger worked fine.

Titan Go V15 The external trigger type menu options ([Audio], [DMX], [GPIO], [MIDI] and [Streaming ACN]) are always shown as being 0/0 I doubt a repro is necessary, but for clarity, repro as follows - 1. Start new show 2. Enter "System" menu and choose [Triggers] 3. Select [Add New] and en...

Has this been resolved? I think this could be solved with a simple macro, here is one I use... <?xml version="1.0" encoding="utf-8"?> <avolites.macros> <macro id="Avolites.Macros.TapTempoBPMMmasters-1-2" name="Tap Tempo on BPM Masters 1&amp;2"> <descriptio...

Titan Go V15 I didn't spend much time trying to asses this so not sure where the problem is specifically but having a Pre-Spool value with Animation Spawn Rate set to values greater than 1 and/or Animation Speed to values less than 1 within pixel maps seems to cause the Pre-Spool effect to produce u...

Titan Go V15 Autoloaded chases do not "Go" when autoloaded with [Go on Target] option. Repro as follows - 1. Start new show 2. Create a 4 step chase 3. Set Link on each step of chase to [Wait For Go] 4. Create a 2 cue list 5. Add the previously created chase to the Autoload for each cue of...